Post by lay1014 on Jun 1, 2020 2:16:30 GMT -5
oil-free vacuum pump in electronic acceleration
In order to meet the rapidly changing needs of customers in the electronics and semiconductor industry, oil-free vacuum pump company has been shortening the product development cycle, launching new products faster, and significantly improving the quality of service. An electron accelerator is usually an electron induction accelerator. An induction accelerator is a device that uses an induced electric field to accelerate electrons. The electron induction accelerator can be used for low energy photon nuclear reaction and activation analysis and other radiation sources.
When the energy is lower than tens of megavolts, the electron induction accelerator is easy to manufacture, easy to adjust and relatively cheap. Therefore, it is widely used in all aspects of the national economy. It is mainly used in industrial gamma ray testing and cancer radiotherapy (using electronic or gamma rays). More than 100 of these accelerators operate in the world, most of them below 20 to 30 MeV. The energy of industrial flaw detection and medical electronic induction accelerator produced in China is 25 MeV.
The electron induction accelerator can also be used in low energy photon nuclear reaction and activation analysis and other radiation sources.
The working principle of imported oil-free vacuum pump is the same as that of ordinary positive displacement pump. It consists of main components, such as stator, rotor, rotor, air cylinder and motor. The rotor with rotating blades is installed eccentrically in the fixed cylinder. When the rotor rotates at high speed, four radial sliding blades in the rotor slot divide the pump cavity into four working cavities. Due to centrifugal force, the rotating blades are tightly attached. The cylinder wall separates the stator inlet and outlet and begins to operate repeatedly to change the volume. The inhaled gas is discharged from the exhaust port to achieve the purpose of pumping.
During use, the ambient temperature of the oil-free vacuum pump shall be lower than 40 ° C, and the temperature rise of the motor shall not exceed 75 ° C. After the normal operation of the magnetic pump for 1000 hours, it is necessary to remove the wear of the bearing and the end moving ring, and replace the vulnerable parts that cannot be reused. For the medium easy to precipitate and crystallize, the medium shall be cleaned immediately after use and discharged into the pump. The vacuum pump must always be clean. No other objects should be placed on the vacuum pump. Do not block the passage around the pump for better maintenance and operation.
Roots Vacuum Pump
Dry Scroll Vacuum Pump
Dry Screw Vacuum Pump
In order to meet the rapidly changing needs of customers in the electronics and semiconductor industry, oil-free vacuum pump company has been shortening the product development cycle, launching new products faster, and significantly improving the quality of service. An electron accelerator is usually an electron induction accelerator. An induction accelerator is a device that uses an induced electric field to accelerate electrons. The electron induction accelerator can be used for low energy photon nuclear reaction and activation analysis and other radiation sources.
When the energy is lower than tens of megavolts, the electron induction accelerator is easy to manufacture, easy to adjust and relatively cheap. Therefore, it is widely used in all aspects of the national economy. It is mainly used in industrial gamma ray testing and cancer radiotherapy (using electronic or gamma rays). More than 100 of these accelerators operate in the world, most of them below 20 to 30 MeV. The energy of industrial flaw detection and medical electronic induction accelerator produced in China is 25 MeV.
The electron induction accelerator can also be used in low energy photon nuclear reaction and activation analysis and other radiation sources.
The working principle of imported oil-free vacuum pump is the same as that of ordinary positive displacement pump. It consists of main components, such as stator, rotor, rotor, air cylinder and motor. The rotor with rotating blades is installed eccentrically in the fixed cylinder. When the rotor rotates at high speed, four radial sliding blades in the rotor slot divide the pump cavity into four working cavities. Due to centrifugal force, the rotating blades are tightly attached. The cylinder wall separates the stator inlet and outlet and begins to operate repeatedly to change the volume. The inhaled gas is discharged from the exhaust port to achieve the purpose of pumping.
During use, the ambient temperature of the oil-free vacuum pump shall be lower than 40 ° C, and the temperature rise of the motor shall not exceed 75 ° C. After the normal operation of the magnetic pump for 1000 hours, it is necessary to remove the wear of the bearing and the end moving ring, and replace the vulnerable parts that cannot be reused. For the medium easy to precipitate and crystallize, the medium shall be cleaned immediately after use and discharged into the pump. The vacuum pump must always be clean. No other objects should be placed on the vacuum pump. Do not block the passage around the pump for better maintenance and operation.
Roots Vacuum Pump
Dry Scroll Vacuum Pump
Dry Screw Vacuum Pump
